国产爆乳无码在线观看-国产爆乳一区不卡在线-国产爆乳尤妮丝无码视频在线-国产边按摩边被躁在线播放-国产边打电话边被躁视频-国产边靠边叫麻豆av

Welcome to visit aluminium alloy die casting factory——Jinjuqiwei official website!
Aluminum Alloy Die Casting Factory
Service Hotline

086-757-25500218

[email protected]
Aluminum Alloy Die Casting Factory

Structural Design Experience of Aluminum Die Castings

Time:2017-9-5 Click:Second

1. Considering the wall thickness, the excessive thickness gap will affect the filling.

2. Consider the demoulding problem, which is very important in the practice of aluminium die casting. Such problems often appear in reality. This is much more difficult to deal with than injection moulding, so the setting of drawing slope and the calculation of the release force of the dynamic and fixed moulds should be paid special attention. Usually, the drawing slope is 1-3 degrees. Usually, considering the smoothness of the demoulding, the slope of the exterior drawing die is smaller than that of the interior drawing die, and the exterior drawing die is about 1 degree, while the interior drawing die is about 2-3 degrees.

3. Considering the problem of die design, if there are many centering positions in different directions, try to put both ends, and the best way is not to put the bottom centering, which will easily lead to problems if the time is too long.

4. The appearance of some die castings can have special requirements, such as injection, powder injection, etc. At this time, the layout should avoid the important appearance orientation to facilitate the setting of gate overflow groove.

5. Avoid presenting the layout as far as possible, which will lead to the complex layout of the die, such as having to use multiple centers or spiral centers.


6. For the parts that need surface processing, attention should be paid to the need to give appropriate processing allowance in the design of the parts, not too much, otherwise the air holes inside will be exposed, not too little, or rough and precise positioning of a processing, black skin has not been disposed of, you wait for sparks on the die, then how much, the best allowance should not be greater than 0.8mm, so that the processed surface. The stomata can hardly be seen because of the protection of hard layer.

7. What's more, we should pay attention to material selection, such as ADC12 or A380, depending on the specific requirements.

8. Aluminum alloy has no elasticity, so long as it cooperates with plastic, it should be fastened.

9. Usually we can't make deep holes! When opening the die, only a few holes are made and then processed.

10. If it is a thin-walled part, it should not be too thin, and must use reinforced ribs to increase flexural capacity! Because the temperature of aluminium castings is about 800 degrees Celsius! Die life is usually relatively short, usually made as the motor shell, if only about 80K will be damaged!

This article is organized by Foshan Jinju Qiwei Die Casting Co., Ltd., a die-casting manufacturer. The service hotline of aluminium alloy die-casting is 0757-25500218! Website: http://www.ldauto.cn/.

Tel

086-757-25500218

在線溝通

主站蜘蛛池模板: 国产精品女同在线调教 | 国产后入又长又硬 | 国产精品系列在线一区 | 国产午夜福利九区在线观看 | 国产成人免费av片在线观看 | 精品人妻va出轨中文字幕 | 精品国产日韩一区二区三区 | 成人无码电影 | 国产91福利精品免费观看 | 国内精品一区二区三区蜜桃 | 国产精品影片在线免费观看 | 国产午夜精品懂色 | 国产亚洲日韩a欧美在线 | 国产爆乳无码在线观看 | 国产免费高清在线视频观看网 | 韩国午夜理伦三级在线观看仙踪林 | 国产成人精品免费视频大全可播 | 1024国产在线| 国产熟女高潮精品视频av | av日韩国产在线 | 国产成人精品电影在线观看 | 东京热久久综合久久 | 加勒比色综合久久久久久久久 | 国产炮机主播在线观看 | 国产av一区精品果冻传媒 | 国产一二三区四区20 | 国产精品欧美一区二区在线看 | 国产欧美日韩亚洲更新 | 国产自慰网址 | 国产欧美日韩欧美特级 | 国产精品无码素人福利免费 | 国产美女裸体无遮掩免费牛牛 | 福利姬一区二区三区在线观看 | 国产av无码乱码国产精品 | 国产成人免费永 | 国产丝袜无码视 | 国产欧美精品综合日韩 | www在线观看一区二区三区 | 91精品国产无码在线观看 | 国产萌白酱喷水视 | 国产欧美日韩一区二区三区在线 |